Вот, что выдает smartctl:
smartctl version 5.33 [i386-portbld-freebsd5.3] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3200826AS
Serial Number: 3ND0496D
Firmware Version: 3.01
User Capacity: 200,048,565,760 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Nov 10 23:34:06 2005 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 67) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 049 045 006 Pre-fail Always - 118057855
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 64
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 136661343
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3223
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 79
194 Temperature_Celsius 0x0022 041 057 000 Old_age Always - 41 (Lifetime Min/Max 0/18)
195 Hardware_ECC_Recovered 0x001a 049 045 000 Old_age Always - 118057855
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 203 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 203 occurred at disk power-on lifetime: 3182 hours (132 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e9 49 e7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e e9 49 e7 00 00:10:49.239 SET MAX ADDRESS EXT
27 00 01 af f1 49 e0 00 00:10:49.239 READ NATIVE MAX ADDRESS EXT
29 00 01 af f1 49 e0 00 00:10:49.239 READ MULTIPLE EXT
37 00 00 af f1 49 e7 00 00:10:49.176 SET MAX ADDRESS EXT
27 00 00 00 00 00 e0 00 00:10:49.095 READ NATIVE MAX ADDRESS EXT
Error 202 occurred at disk power-on lifetime: 3121 hours (130 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e9 49 e7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e e9 49 e7 00 00:12:11.257 SET MAX ADDRESS EXT
27 00 01 af f1 49 e0 00 00:12:11.114 READ NATIVE MAX ADDRESS EXT
29 00 01 af f1 49 e0 00 00:12:11.114 READ MULTIPLE EXT
37 00 00 af f1 49 e7 00 00:12:11.114 SET MAX ADDRESS EXT
27 00 00 00 00 00 e0 00 00:12:09.642 READ NATIVE MAX ADDRESS EXT
Error 201 occurred at disk power-on lifetime: 3103 hours (129 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e9 49 e7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e e9 49 e7 00 03:39:05.410 SET MAX ADDRESS EXT
27 00 01 af f1 49 e0 00 03:39:05.410 READ NATIVE MAX ADDRESS EXT
29 00 01 af f1 49 e0 00 03:39:05.410 READ MULTIPLE EXT
37 00 00 af f1 49 e7 00 03:39:05.410 SET MAX ADDRESS EXT
27 00 00 00 00 00 e0 00 03:39:05.409 READ NATIVE MAX ADDRESS EXT
Error 200 occurred at disk power-on lifetime: 3103 hours (129 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e9 49 e7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e e9 49 e7 00 03:22:51.799 SET MAX ADDRESS EXT
27 00 01 af f1 49 e0 00 03:22:51.718 READ NATIVE MAX ADDRESS EXT
29 00 01 af f1 49 e0 00 03:22:53.551 READ MULTIPLE EXT
37 00 00 af f1 49 e7 00 03:22:53.551 SET MAX ADDRESS EXT
27 00 00 00 00 00 e0 00 03:22:53.404 READ NATIVE MAX ADDRESS EXT
Error 199 occurred at disk power-on lifetime: 3101 hours (129 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e e9 49 e7
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e e9 49 e7 00 01:14:50.521 SET MAX ADDRESS EXT
27 00 01 af f1 49 e0 00 01:14:50.521 READ NATIVE MAX ADDRESS EXT
29 00 01 af f1 49 e0 00 01:14:50.520 READ MULTIPLE EXT
37 00 00 af f1 49 e7 00 01:14:50.520 SET MAX ADDRESS EXT
27 00 00 00 00 00 e0 00 01:14:50.462 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.