icmp, IPPROTO_ICMP - Linux IPv4 ICMP kernel module.
DESCRIPTION
This kernel protocol module implements the Internet Control
Message Protocol defined in RFC 792.
It is used to signal error conditions and for diagnosis.
The user doesn't interact directly with this module;
instead it communicates with the other protocols in the kernel
and these pass the ICMP errors to the application layers.
The kernel ICMP module also answers ICMP requests.
A user protocol may receive ICMP packets for all local sockets by opening
a raw socket with the protocol
IPPROTO_ICMP.
See
raw(7)
for more information.
The types of ICMP packets passed to the socket can be filtered using the
ICMP_FILTER
socket option.
ICMP packets are always processed by the kernel too, even
when passed to a user socket.
Linux limits the rate of ICMP error packets to each destination.
ICMP_REDIRECT
and
ICMP_DEST_UNREACH
are also limited by the destination route of the incoming packets.
/proc interfaces
ICMP supports a set of
/proc
interfaces to configure some global IP parameters.
The parameters can be accessed by reading or writing files in the directory
/proc/sys/net/ipv4/.
Most of these parameters are rate limitations for specific ICMP types.
Linux 2.2 uses a token bucket filter to limit ICMPs.
The value is the timeout in jiffies until the token bucket filter is
cleared after a burst.
A jiffy is a system dependent unit, usually 10ms on i386 and
about 1ms on alpha and ia64.
icmp_destunreach_rate (Linux 2.2 to 2.4.9)
Maximum rate to send ICMP Destination Unreachable packets.
This limits the rate at which packets are sent to any individual
route or destination.
The limit does not affect sending of
ICMP_FRAG_NEEDED
packets needed for path MTU discovery.
icmp_echo_ignore_all (since Linux 2.2)
If this value is non-zero, Linux will ignore all
ICMP_ECHO
requests.
icmp_echo_ignore_broadcasts (since Linux 2.2)
If this value is non-zero, Linux will ignore all
ICMP_ECHO
packets sent to broadcast addresses.
icmp_echoreply_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending
ICMP_ECHOREPLY
packets in response to
ICMP_ECHOREQUEST
packets.
icmp_errors_use_inbound_ifaddr (Boolean; default: disabled; since Linux 2.6.12)
If disabled, ICMP error messages are sent with the primary address of
the exiting interface.
If enabled, the message will be sent with the primary address of
the interface that received the packet that caused the ICMP error.
This is the behavior that many network administrators will expect from
a router.
And it can make debugging complicated network layouts much easier.
Note that if no primary address exists for the interface selected,
then the primary address of the first non-loopback interface that
has one will be used regardless of this setting.
icmp_ignore_bogus_error_responses (Boolean; default: disabled; since Linux 2.2)
Some routers violate RFC1122 by sending bogus responses to broadcast frames.
Such violations are normally logged via a kernel warning.
If this parameter is enabled, the kernel will not give such warnings,
which will avoid log file clutter.
icmp_paramprob_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending
ICMP_PARAMETERPROB
packets.
These packets are sent when a packet arrives with an invalid IP header.
icmp_ratelimit (integer; default: 1000; since Linux 2.4.10)
Limit the maximum rates for sending ICMP packets whose type matches
icmp_ratemask
(see below) to specific targets.
0 to disable any limiting,
otherwise the minimum space between responses in milliseconds.
icmp_ratemask (integer; default: see below; since Linux 2.4.10)
Mask made of ICMP types for which rates are being limited.
Bit definitions (see the kernel source file
include/linux/icmp.h):
0 Echo Reply
3 Destination Unreachable *
4 Source Quench *
5 Redirect
8 Echo Request
B Time Exceeded *
C Parameter Problem *
D Timestamp Request
E Timestamp Reply
F Info Request
G Info Reply
H Address Mask Request
I Address Mask Reply
The bits marked with an asterisk are rate limited by default
(see the default mask above).
icmp_timeexceed_rate (Linux 2.2 to 2.4.9)
Maximum rate for sending
ICMP_TIME_EXCEEDED
packets.
These packets are
sent to prevent loops when a packet has crossed too many hops.
VERSIONS
Support for the
ICMP_ADDRESS
request was removed in 2.2.
Support for
ICMP_SOURCE_QUENCH
was removed in Linux 2.2.
NOTES
As many other implementations don't support
IPPROTO_ICMP
raw sockets, this feature
should not be relied on in portable programs.
ICMP_REDIRECT
packets are not sent when Linux is not acting as a router.
They are also only accepted from the old gateway defined in the
routing table and the redirect routes are expired after some time.
The 64-bit timestamp returned by
ICMP_TIMESTAMP
is in milliseconds since January 1, 1970.
Linux ICMP internally uses a raw socket to send ICMPs.
This raw socket may appear in
netstat(8)
output with a zero inode.
This page is part of release 3.14 of the Linux
man-pages
project.
A description of the project,
and information about reporting bugs,
can be found at
http://www.kernel.org/doc/man-pages/.
