[ новости /+++ | форум | теги | ]

NAME

snmpusm - creates and maintains SNMPv3 users on a network entity
 

SYNOPSIS

DESCRIPTION

OPTIONS

-Ca

Change the authentication key.

-Cx

Change the privacy key.

-Ck

Use old localized key instead of old passphrase. When this option is used, either the -Ca or -Cx (but not both) option must also be used.

CREATING USERS

An unauthenticated SNMPv3 user can be created using the command

snmpusm create USER

This constructs an (inactive) entry in the usmUserTable, with no authentication or privacy settings. In principle, this user should be useable for 'noAuthNoPriv' requests, but in practise the Net-SNMP agent will not allow such an entry to be made active.

In order to activate this entry, it is necessary to "clone" an existing user, using the command

snmpusm cloneFrom USER CLONEFROM-USER

The USER entry then inherits the same authentication and privacy settings (including pass phrases) as the CLONEFROM user.

These two steps can be combined into one, by using the command

snmpusm create USER CLONEFROM-USER

The two forms of the create sub-command require that the user being created does not already exist. The cloneFrom sub-command requires that the user being cloned to does already exist.

Cloning is the only way to specify which authentication and privacy protocols to use for a given user, and it is only possible to do this once. Subsequent attempts to reclone onto the same user will appear to succeed, but will be silently ignored. This (somewhat unexpected) behaviour is mandated by the SNMPv3 USM specifications (RFC 2474). To change the authentication and privacy settings for a given user, it is necessary to delete and recreate the user entry. This is not necessary for simply changing the pass phrases (see below). This means that the agent must be initialized with at least one user for each combination of authentication and privacy protocols. See the snmpd.conf(5) manual page for details of the createUser configuration directive.

DELETING USERS

snmpusm delete USER

CHANGING PASS PHRASES

snmpusm [-Ca] [-Cx] passwd OLD-PASSPHRASE NEW-PASSPHRASE [USER]

After cloning a new user entry from the appropriate template, you should immediately change the new user's passphrase.

If USER is not specified, this command will change the passphrase of the (SNMPv3) user issuing the command. If the -Ca or -Cx options are specified, then only the authentication or privacy keys are changed. If these options are not specified, then both the authentication and privacy keys are changed.

snmpusm [-Ca] [-Cx] changekey [USER]

This command changes the key in a perfect-forward-secrecy compliant way through a diffie-helman exchange. The remote agent must support the SNMP-USM-DH-OBJECTS-MIB for this command to work. The resulting keys are printed to the console and may be then set in future command invocations using the --defAuthLocalizedKey and --defPrivLocalizedKey options or in your snmp.conf file using the defAuthLocalizedKey and defPrivLocalizedKey keywords.

Note that since these keys are randomly generated based on a diffie helman exchange, they are no longer derived from a more easily typed password. They are, however, much more secure.

To change from a localized key back to a password, the following variant of the passwd sub-command is used:

snmpusm <-Ca | -Cx> -Ck passwd OLD-LOCALIZED-KEY NEW-PASSPHRASE [USER]

Either the -Ca or the -Cx option must be specified. The OLD-LOCALIZED-KEY parameter is the localized key that was printed out by the changekey sub-command.

EXAMPLES

Let's assume for our examples that the following VACM and USM configurations lines were in the snmpd.conf file for a Net-SNMP agent. These lines set up a default user called "initial" with the authentication passphrase "setup_passphrase" so that we can perform the initial setup of an agent:

# VACM configuration entries
rwuser initial
# lets add the new user we'll create too:
rwuser wes
# USM configuration entries
createUser initial MD5 setup_passphrase DES

Note: the "initial" user's setup should be removed after creating a real user that you grant administrative privileges to (like the user "wes" we'll be creating in this example.

Note: passphrases must be 8 characters minimum in length.  

Create a new user

snmpusm -v3 -u initial -n "" -l authNoPriv -a MD5 -A setup_passphrase localhost create wes initial

Creates a new user, here named "wes" using the user "initial" to do it. "wes" is cloned from "initial" in the process, so he inherits that user's passphrase ("setup_passphrase").

Change the user's passphrase

snmpusm -v 3 -u wes -n "" -l authNoPriv -a MD5 -A setup_passphrase localhost passwd setup_passphrase new_passphrase

After creating the user "wes" with the same passphrase as the "initial" user, we need to change his passphrase for him. The above command changes it from "setup_passphrase", which was inherited from the initial user, to "new_passphrase".

Test the new user

snmpget -v 3 -u wes -n "" -l authNoPriv -a MD5 -A new_passphrase localhost sysUpTime.0

If the above commands were successful, this command should have properly performed an authenticated SNMPv3 GET request to the agent.

Now, go remove the vacm "group" snmpd.conf entry for the "initial" user and you have a valid user 'wes' that you can use for future transactions instead of initial.

WARNING

SEE ALSO

Index

NAME

SYNOPSIS

DESCRIPTION

OPTIONS

CREATING USERS

DELETING USERS

CHANGING PASS PHRASES

EXAMPLES

Create a new user

Change the user's passphrase

Test the new user

WARNING

SEE ALSO

Партнёры:

Хостинг: